hydraulic meter| magmeter flow meter

『hydraulic meter|thermal flow meter』Related information(clamp on meter|electromagnetic meter|venturi meterrotameter|orifice meter|ultrasonic flow meter|mass flow meter|coriolis mass flow meter|coriolis flow meter|magnetic flow meter|magmeter flow meter|magflow flow meter|mag meter flow meter|electromagnetic flow meter|vortex flow meter|turbine flow meter|thermal mass flow meter|thermal flow meter|rotameter flow meter)

What are some professional terms and abbreviations for oil drilling in English?

1. Bottom Hole Assembly - Downhole Drilling Tool Assembly 2. Maintain the Angle - Steady Tilt 3. Rigid Packet Hole Assembly - Rigid Full Hole Drilling Tool Assembly 4. Pendulum Drill Assembly - Pendulum Drilling Tool Assembly 5. Straighten the Hole - Correction Tilt 6. Tapped Drill Assembly - Tower Drilling Tool Assembly 7. Stabilizer - Corrector 8. Anti Deviation 9. Reasonable 10 The reasonable length of the bottom hole assembly depends on the weight on bit. Normally, the maximum weight on bit is roughly equal to 70% of the total weight of the bottom hole assembly. - The rationality of the length of the downhole drilling tool assembly depends on the weight on the drill bit. Usually, the maximum weight of the drill bit is approximately 70% of the total weight of the downhole drilling tool assembly. 11. Up to standard - Achieve standard 12. Packet hole Stabilizer=Full Hole Stabilizer - Full Hole Stabilizer 13. Down Hole Complicated Condition - Complicated downhole conditions 14. Drilling Assembly - Drilling tool assembly 15. Drilling Jar - Shock absorber while drilling 16. Heavy Wall Drill Pipe - Weighted drill pipe 17. Shock absorber - Shock absorber 18 To reduce the excessive impact on a drilling bit so as to prolong the life of the bit - In order to reduce excessive impact on the drill bit and extend its service life by 19 Fishing Assembly - Fishing Drill Tool Assembly 20. Make up Sub, Safety Sub, Drilling Jar, Drill Collar, and Accelerator - Matching Joints, Safety Joints, Drilling Shakers, Drill Collars, and Accelerators 21 Slip Socket - Kava Fishing Barrel 22 At the bottom of the drill-string assembly, the 150 m drill pipe

shall be used when the deviation angle is between 0 ° and 35 °, the 250 to 300 m heavy drill pipe is used between 35 ° and 80 °, and the 300 to 400 m heavy drill pipe is used at 80 ° and above. - At the bottom of the drilling rig assembly, a 150 meter drill pipe should be used when the deviation angle is between 0 ° and 35 °; A heavy drilling rod of 250 to 300 meters should be used between 35 ° and 80 °; Heavy drill pipes of 300 to 400 meters should be used for angles of 80 ° and above. 23. Power Drilling Assembly - Downhole Power Drilling Tool Assembly 24 It consists of drilling bit, power drilling tool, bent sub, non-magnetic drill collar, six drill collars, and twelve heavy wall drill pipe - It includes drill bits, power drilling tools, bent joints, non-magnetic drill collars, six drill collars, and twelve weighted drill rods S135 means that the tensile strength is 135 psi. - S135 means a tensile strength of 135 pounds force per square inch. 26. Safety Slip 27. Fingerboard 28. Small Holist 29. Neutral Point 30 Once every three months for continuous operation - For continuous operations, once every three months Mud Non Corrosive Ring 32. Hydraulic Power Station 33. Scraper 34. Automatic Trip In Devices 35. Sensor 36. Trip Tank=Meter Tank 37. Slug the Drill Pipe 38. Pump Stroke 39. Mud Saver 40. Doghouse 41. Dies, Jaws, Hydraulic Tong 42. Claws, heads, hydraulic tongs 42 Lifting Sub - Lifting Short Section 43. 18 Degrees Shoulder Elevator -18 Degree Slope Elevator 44. Cock - Plug 45. Rope - Wire Rope 46. Monkey Board - Second Floor Platform 47. Hammer and Adjustable Wrench 48. Hammer and Adjustable Wrench 48 Escape Equipment - Escape Device 49. Derrick - Derrick - Derrick 50. Crown-O-Matic - Anti collision Crane 51. Ad

hydraulic meter

What are some professional terms and abbreviations for oil drilling in English?

『SILVER Official Website SERVICE』